My contact person
igus® inc.

PO BOX 14349

East Providence

RI 02914

+1 800 521 2747
+1 401 438 7270
igus® inc.

Vice President

East Providence, RI

+1 401 438 2200
+1 401 438 7270

Bar stock - iglide®

Bar stock for motion
iglide® plastic bar stock for motion runs without lubrication and maintenance, achieves the lowest friction and wear values, thus increasing the service life of the application - especially for prototypes, test samples or smaller quantity requirements.
 
iglide® plastic bar stock are available from stock in various standard iglide® materials as rods, tubes, film sheets and plates; other materials and special shapes such as plastic profiles or finish machined drawing parts are available on request. Finished standard parts such as trapezoidal threaded nuts, knife edge rollers, sliding plates and spherical balls are cost-effective and readily available from stock.
 
The plastic bar stock suitable for temperatures up to +482°F, are available with approvals for food and drinking water applications, as well as for other specialist use such as in the tobacco industry, etc. 
 

Products

Filter

Application Requirements
Certifications and approvals
Material

Number of products: 27

iglide® J, round bar
  • Low wear against a lot of shaft materials
  • Low coefficients of friction during dry operation
  • Vibration dampening
  • Good resistance to chemicals
  • Best performance with soft shaft materials
  • Low moisture absorption

from 10.30 USD / m

Available on request
Shop now
iglide® R, round bar
  • Very cost-effective
  • Good abrasion resistance
  • Low coefficients of friction during dry operation
  • Low moisture absorption

from 47.78 USD / m

Available on request
Shop now
iglide® M250, round bar
  • Excellent vibration dampening
  • Resistant to edge loads
  • High impact resistance

from 28.82 USD / m

Available on request
Shop now
iglide® A160, round bar
  • Compliant with EC regulation 10/2011 EC, FDA-compliant
  • High media resistance
  • self lubricating and maintenance-free

from 36.00 USD / m

Available on request
Shop now
iglide® L280, round bar
  • For a long service life during continuous operation
  • Low coefficient of friction
  • Extremely high abrasion resistance
  • Suitable for rugged and stainless-steel shafts
  • Dirt-resistant

Upon request

Available on request
Shop now
iglidur® T500, round bar
  • Continuous operating temperatures from -140 to +480 °F
  • Extremely high chemical resistance
  • Fulfils the fire prevention requirements of the Federal Aviation Administration of the USA (FAA) for aircraft interiors
  • High compressive strength

from 82.19 USD / m

Available on request
Shop now
iglide® A181, round bar
  • Suitable for temperatures up to +190 °F
  • FDA and EC regulation 10/2011 EC compliant
  • Good media resistance

from 20.08 USD / m

Available on request
Shop now
iglide® A500, round bar
  • Compliant with EC regulation 10/2011 EC, FDA-compliant
  • Temperature resistant from -100 °C to +250 °C
  • High chemical resistance

Upon request

Available on request
Shop now
iglide® A180, round bar
  • Complies with food and drug administration (FDA) regulations for repeated contact with food
  • Good media resistance
  • For wet environments
  • High wear resistance

from 9.91 USD / m

Available on request
Shop now
iglide® A350, round bar
  • For temperatures up to +350 °F
  • FDA compliant
  • For medium to high loads
  • Suitable for both oscillating and rotating applications
  • Fulfills the fire prevention requirements of the Federal Aviation Administration of the USA (FAA) for aircraft interiors
  • Self-lubricating and maintenance-free

from 38.02 USD / m

Available on request
Shop now
iglide® J3, round bar
  • Specialist for pivoting and pulsating loads
  • Good media resistance
  • Low moisture absorption
  • PTFE-free

from 18.69 USD / m

Available on request
Shop now
iglide® H1, round bar
  • High wear resistance in extreme ambient conditions
  • Very low coefficients of friction
  • High resistance to temperature and chemicals
  • For underbonnet applications
  • Lubrication and maintenance-free

from 196.62 USD / m

Available on request
Shop now
iglide® J2, round bar
  • Good mechanical properties, robust
  • Cost-effective
  • Good media resistance
  • Self-lubricating and maintenance-free

from 146.97 USD / m

Available on request
Shop now
iglide® J4, round bar
  • Self-lubricating and maintenance-free
  • Low-cost material for mass production
  • Low coefficients of friction
  • Good media resistance
  • Low moisture absorption

from 22.00 USD / m

Available on request
Shop now
iglide® P210, round bar
  • Low moisture absorption
  • Good coefficients of friction and wear on almost every shaft
  • Good price/performance ratio

from 80.23 USD / m

Available on request
Shop now

Consulting

I would be happy to answer your questions personally!

Photo
Preston Souza

Product Manager robolink, 3D printing, PRT, barstock

Write e-mail

Shipping and consultation

In person:

Monday to Friday from 7 am - 8 pm

Online:

24h